Check items to add to the cart or select all
Product Description
Like Perseus's sword dropped from the heavens by Zeus himself, DCC introduces our DIY Cafe Racer rear tail hoop section enabling those who wield it the ability to conquer the streets by day and win the ladies by night.
Alright, it's not near as cool as Perseus's sword, and your probably not gonna get any chicks with it, but we made you laugh right?
The DCC Crew knows how hard it is to build the perfect rear hoop section for that Cafe creation your bringing to life in your garage. We've been there...trust us!
Using one of those orange Harbor Freight benders? Can't get the angles just right? Wasted 25' of tubing trying to get the right look? Well, look no further Ace. As usual, DCC has you covered! We've done the math and invested in a custom die for our tube bender that creates a perfect radius and tail section even the gods would smile upon.
All you need to check is the outside diameter of your frame tubes and the distance between them where your going to cut the back section off. The Wing'd Piston takes care of the rest!
Manufactured right here in Dime City out of cold rolled 1" .095wall DOM steel tubing, we put the bricks to the bender and kick out these super sweet tails just for you. We leave an extra 7" on each side so you can cut it to match the length of your seat for that perfect custom look right in your garage!
Installation is simple, just cut off the back half of your frame (at your own risk), chamfer the edges of the frame and the tube, get a buddy to hold it in place and weld away. Just smooth out the welds with a flap wheel and grinder and paint or powder coat it to your liking!
As a standard we offer them completely straight out and flat, but for those looking for a little more racey look, we put a slight bend right before the main radius creating a nice upward slope and a more modern and progressive stance.
Just fab up your seat to match or trim your Roccity or Legendary Motorcycles Cafe Racer glass seat to fit and your good to go! Just make sure you measure your frame rails center to center to select the proper hoop as we do offer two sizes. Typically, the smaller one is good for most 350cc to 500cc bikes and the larger loop (this one) is good for just about anything over 500cc.
And remember, if your frame is slightly wider or skinnier, don't fret. Get the one closest and with some patience, a little heat and some additional welding and cutting you can most likely get a perfect fit!
Man, it's a good thing the Dime City Crew is looking out for ya 'eh?
Alright, it's not near as cool as Perseus's sword, and your probably not gonna get any chicks with it, but we made you laugh right?
The DCC Crew knows how hard it is to build the perfect rear hoop section for that Cafe creation your bringing to life in your garage. We've been there...trust us!
Using one of those orange Harbor Freight benders? Can't get the angles just right? Wasted 25' of tubing trying to get the right look? Well, look no further Ace. As usual, DCC has you covered! We've done the math and invested in a custom die for our tube bender that creates a perfect radius and tail section even the gods would smile upon.
All you need to check is the outside diameter of your frame tubes and the distance between them where your going to cut the back section off. The Wing'd Piston takes care of the rest!
Manufactured right here in Dime City out of cold rolled 1" .095wall DOM steel tubing, we put the bricks to the bender and kick out these super sweet tails just for you. We leave an extra 7" on each side so you can cut it to match the length of your seat for that perfect custom look right in your garage!
Installation is simple, just cut off the back half of your frame (at your own risk), chamfer the edges of the frame and the tube, get a buddy to hold it in place and weld away. Just smooth out the welds with a flap wheel and grinder and paint or powder coat it to your liking!
As a standard we offer them completely straight out and flat, but for those looking for a little more racey look, we put a slight bend right before the main radius creating a nice upward slope and a more modern and progressive stance.
Just fab up your seat to match or trim your Roccity or Legendary Motorcycles Cafe Racer glass seat to fit and your good to go! Just make sure you measure your frame rails center to center to select the proper hoop as we do offer two sizes. Typically, the smaller one is good for most 350cc to 500cc bikes and the larger loop (this one) is good for just about anything over 500cc.
And remember, if your frame is slightly wider or skinnier, don't fret. Get the one closest and with some patience, a little heat and some additional welding and cutting you can most likely get a perfect fit!
Man, it's a good thing the Dime City Crew is looking out for ya 'eh?
Product Tags
Add Your Tags:
Use spaces to separate tags. Use single quotes (') for phrases.
