Free Shipping - US orders over $100. Canada over $199. See details.

DCC Originals DIY Custom Rear Tail Hoop for Large CC Bikes

DCC Originals DIY Custom Rear Tail Hoop for Large CC Bikes

Quick Overview

Color/Finish: Raw SteelFits:Large CC Honda's, Kawasaki's, Yamaha's and Suzuki's Harley Davidson Sportser 04+Other Makes & Models w/ Center to Center Tube Measurement of 8" - 8-1/8"Material: 1" or 7/8", DOM Steel TubingDimensions:End to Radius 7" w/ 4" on center 180 Degree RadiusInstallation Notes: Depending upon where you cut your frame and where you cut the tail upon receipt you may need to open or close the gap a bit. This can be done easily by putting one end of the tail in a vice, locking it down, and using a longer piece of steel to pull, or open the gap.In the same respect you can close the gap by simply putting a ratchet strap around the ends tightening it in order to get the fitment spot on with your frame.â–º Make sure you pickup a set of universal frame slugs to ensure a SAFE installation.
*Angle on Upswept version is approximately 25 degrees.

* Required Fields



Like Perseus's sword dropped from the heavens by Zeus himself, DCC introduces our DIY Cafe Racer rear tail hoop section enabling those who wield it the ability to conquer the streets by day and win the ladies by night.

Alright, it's not near as cool as Perseus's sword, and your probably not gonna get any chicks with it, but we made you laugh right?

The DCC Crew knows how hard it is to build the perfect rear hoop section for that Cafe creation your bringing to life in your garage. We've been us!

Using one of those orange Harbor Freight benders? Can't get the angles just right? Wasted 25' of tubing trying to get the right look? Well, look no further Ace. As usual, DCC has you covered! We've done the math and invested in a custom die for our tube bender that creates a perfect radius and tail section even the gods would smile upon.

All you need to check is the outside diameter of your frame tubes and the distance between them where your going to cut the back section off. The Wing'd Piston takes care of the rest!

Manufactured right here in Dime City out of cold rolled 1" .095wall DOM steel tubing, we put the bricks to the bender and kick out these super sweet tails just for you. We leave an extra 7" on each side so you can cut it to match the length of your seat for that perfect custom look right in your garage!

Installation is simple, just cut off the back half of your frame (at your own risk), chamfer the edges of the frame and the tube, get a buddy to hold it in place and weld away. Just smooth out the welds with a flap wheel and grinder and paint or powder coat it to your liking!

As a standard we offer them completely straight out and flat, but for those looking for a little more racey look, we put a slight bend right before the main radius creating a nice upward slope and a more modern and progressive stance.

Just fab up your seat to match or trim your Roccity or Legendary Motorcycles Cafe Racer glass seat to fit and your good to go! Just make sure you measure your frame rails center to center to select the proper hoop as we do offer two sizes. Typically, the smaller one is good for most 350cc to 500cc bikes and the larger loop (this one) is good for just about anything over 500cc.

And remember, if your frame is slightly wider or skinnier, don't fret. Get the one closest and with some patience, a little heat and some additional welding and cutting you can most likely get a perfect fit!

Man, it's a good thing the Dime City Crew is looking out for ya 'eh?

Technical Details

Brand DCC Originals
Motorcycle Make Honda


Perfect fit for my KZ1000 K2!

Good product, cut and weld it to the frame, looks perfect!



It's round, it's curved, it's angled up 15 degrees......totally sexy! Woo!!!

it is right

Finished out my sportster scrambler just right.

Perfect Fit

The tail loop fit perfectly in my 1979 XS750. The ends were a bit long, but gave me plenty to work with/chop off. Strong product.

large rear tail hoop

With some spreading perfect! With the extra length i was able to cut more off the frame to give it a 1 rider look.
thanks DCC!!!

Great parts

Great parts:)

nice little project

Fit was very close on a 1979 Kawasaki KZ750. Spread the hoop about 1cm to get that perfect fit. Also used the frame slugs from here too. With a little grinding they fit my bikes frame perfectly.

Nice fit

I got the upswept tail hoop and it looks beautiful. with a little clamping, it fit perfect onto my '79 Suzuki GS750 frame

Write Your Own Review

You're reviewing: DCC Originals DIY Custom Rear Tail Hoop for Large CC Bikes

How do you rate this product? *

1 1 star
2 2 star
3 3 star
4 4 star
5 5 star